Listings are for most Transit Vans. You may need additional equipment for your unit.
Call 800-884-3826 to check.
AIR TECH II DIGITAL KIT
Tie to Existing System w/Prep
The AirTech II provides superb heating and cooling for the handicap and luxury van conversion industries. It is designed to produce cooler, consistent temperatures. The dual coil design allows rear heating while the dash system is in defrost mode. The 3 speed permanent magnet motor provides a permanent long lasting operation.
BTU Cooling
30,000
BTU Heating
28,000
CFM
295
Amps at 13.5v
9.5
Dimensions
15W x 9.25D x 12.2H"
Weight
10.5 lbs
This basic kit includes all components need for a complete installation including the above shown evaporator,condenser,hoses, fittings, and electric wiring with relays and switches.
AIR TECH II ROTARY KIT
Tie to Existing System
The AirTech II provides superb heating and cooling for the handicap and luxury van conversion industries. It is designed to produce cooler, consistent temperatures. The dual coil design allows rear heating while the dash system is in defrost mode. The 3 speed permanent magnet motor provides a permanent long lasting operation.
BTU Cooling
30,000
BTU Heating
28,000
CFM
295
Amps at 13.5v
9.5
Dimensions
15W x 9.25D x 12.2H"
Weight
10.5 lbs
This basic kit includes all components need for a complete installation including the above shown evaporator,condenser,hoses, fittings, and electric wiring with relays and switches.
AIR TECH II DUAL SWITCH KIT
Tie to Existing System
The AirTech II provides superb heating and cooling for the handicap and luxury van conversion industries. It is designed to produce cooler, consistent temperatures. The dual coil design allows rear heating while the dash system is in defrost mode. The 3 speed permanent magnet motor provides a permanent long lasting operation.
BTU Cooling
30,000
BTU Heating
28,000
CFM
295
Amps at 13.5v
9.5
Dimensions
15W x 9.25D x 12.2H"
Weight
10.5 lbs
This basic kit includes all components need for a complete installation including the above shown evaporator,condenser,hoses, fittings, and electric wiring with relays and switches.
AIR TECH II DIGITAL KIT
Tie to Existing System
The AirTech II provides superb heating and cooling for the handicap and luxury van conversion industries. It is designed to produce cooler, consistent temperatures. The dual coil design allows rear heating while the dash system is in defrost mode. The 3 speed permanent magnet motor provides a permanent long lasting operation.
BTU Cooling
30,000
BTU Heating
28,000
CFM
295
Amps at 13.5v
9.5
Dimensions
15W x 9.25D x 12.2H"
Weight
10.5 lbs
This basic kit includes all components need for a complete installation including the above shown evaporator,condenser,hoses, fittings, and electric wiring with relays and switches.
526/109/420 KIT
Super Tie to Existing System
The model 526 unit was designed for a medium commuter, shuttle type vehicle. It is used with items that do not require a refrigerated environment. The unit is powered by twin dual bearing, three speed motors.
BTU Cooling
28,000
CFM
460
Amps at 13.5v
21
Dimensions
33.75W x 12D x 5.5H"
Weight
23.5 lbs
This model 109 Frigiking roof or underbody mounted condenser is a way of providing maximum heat transfer during stop and go operations. Featured are twin 11" blades,
white aluminum housing and powder coated galvanized mounting brackets.
BTU Cooling
40,000
CFM
2,800
Amps at 13.5V
15
Dimensions
30W x10H x 13D"
Weight
24 lbs
This basic kit includes all components need for a complete installation including the above shown evaporator, condenser, compressor,holes and fittings, and electric wiring with relays and switches. Additional equipment and or additions listed at the bottom of the page, may be required depending upon your particular Transit.
552/109 KIT
Super Tie to Existing System
The model 552 unit was designed for a small commuter, shuttle type vehicle requires an average amount of extra cooling. It is used with items that do not require a refrigerated environment. The unit is powered by twin dual bearing, three speed motors.
BTU Cooling
22,000
BTU Heating
28,000
CFM
480
Amps at 13.5v
21
Dimensions
33.75W x 5.5H x 12D"
Weight
23.5 lbs
This model 109 Frigiking roof or underbody mounted condenser is a way of providing maximum heat transfer during stop and go operations. Featured are twin 11" blades,
white aluminum housing and powder coated galvanized mounting brackets.
BTU Cooling
40,000
CFM
2,800
Amps at 13.5V
15
Dimensions
30W x10H x 13D"
Weight
24 lbs
This basic kit includes all components need for a complete installation including the above shown evaporator, condenser, compressor,holes and fittings, and electric wiring with relays and switches. Additional equipment and or additions listed at the bottom of the page, may be required depending upon your particular Transit.
530/109
Super Tie to Existing System
The model 530 unit was designed for a small commuter, shuttle type vehicle requires an average amount of extra cooling. It is used with items that do not require a refrigerated environment. The unit is powered by twin dual bearing, three speed motors.
BTU Cooling
30,000
CFM
480
Amps at 13.5v
21
Dimensions
33.75W x 12D x 5.5H"
Weight
23.5 lbs
This model 109 Frigiking roof or underbody mounted condenser is a way of providing maximum heat transfer during stop and go operations. Featured are twin 11" blades,
white aluminum housing and powder coated galvanized mounting brackets.
BTU Cooling
40,000
CFM
2,800
Amps at 13.5V
15
Dimensions
30W x10H x 13D"
Weight
24 lbs
This basic kit includes all components need for a complete installation including the above shown evaporator, condenser, compressor,holes and fittings, and electric wiring with relays and switches. Additional equipment and or additions listed at the bottom of the page, may be required depending upon your particular Transit.
931 KIT
Tie to Existing System
The model 931 unit was designed for a medium commuter, shuttle type vehicle. It is used with items that do not require a refrigerated environment.
BTU Cooling
27,000
BTU Heating
28,000
CFM
630
Amps at 13.5v
16.3
Dimensions
32W x 15.5D x 8.5H"
Weight
26.5 lbs
This basic kit includes all components need for a complete installation including the above shown evaporator, condenser, compressor,holes and fittings, and electric wiring with relays and switches. Additional equipment and or additions listed at the bottom of the page, may be required depending upon your particular Transit.
931/109 KIT
Super Tie to Existing System
The model 931 unit was designed for a medium commuter, shuttle type vehicle. It is used with items that do not require a refrigerated environment.
BTU Cooling
30,000
CFM
550
Amps at 13.5v
21
Dimensions
32W x 15.5D x 8.5H"
Weight
36 lbs
This model 109 Frigiking roof or underbody mounted condenser is a way of providing maximum heat transfer during stop and go operations. Featured are twin 11" blades,
white aluminum housing and powder coated galvanized mounting brackets.
BTU Cooling
40,000
CFM
2,800
Amps at 13.5V
15
Dimensions
30W x10H x 13D"
Weight
24 lbs
This basic kit includes all components need for a complete installation including the above shown evaporator, condenser, compressor,holes and fittings, and electric wiring with relays and switches. Additional equipment and or additions listed at the bottom of the page, may be required depending upon your particular Transit.
530/109 AC KIT
Additional AC System
The model 530 unit was designed for a small commuter, shuttle type vehicle requires an average amount of extra cooling. It is used with items that do not require a refrigerated environment. The unit is powered by twin dual bearing, three speed motors.
BTU Cooling
30,000
CFM
480
Amps at 13.5v
21
Dimensions
33.75W x 12D x 5.5H"
Weight
23.5 lbs
This model 109 Frigiking roof or underbody mounted condenser is a way of providing maximum heat transfer during stop and go operations. Featured are twin 11" blades,
white aluminum housing and powder coated galvanized mounting brackets.
BTU Cooling
40,000
CFM
2,800
Amps at 13.5V
15
Dimensions
30W x10H x 13D"
Weight
24 lbs
Compresor,Hardware,Hozes,Switches
This basic kit includes all components need for a complete installation including the above shown evaporator,condenser,heater,hoses, fittings, and electric wiring with relays and switches.
530/110 AC KIT
Additional AC System
The model 530 unit was designed for a small commuter, shuttle type vehicle requires an average amount of extra cooling. It is used with items that do not require a refrigerated environment. The unit is powered by twin dual bearing, three speed motors.
BTU Cooling
30,000
CFM
480
Amps at 13.5v
21
Dimensions
33.75W x 12D x 5.5H"
Weight
23.5 lbs
This model 110 Frigiking roof or underbody mounted condenser is a way of providing maximum heat transfer during stop and go operations. Featured are three 11" blades, white aluminum housing and powder coated galvanized mounting brackets.
BTU Cooling
60,000
CFM
4200
Amps at 13.5V
22.5
Dimensions
44.5W x 13D x 13H"
Weight
33 lbs
Compresor,Hardware,Hozes,Switches
This basic kit includes all components need for a complete installation including the above shown evaporator,condenser,heater,hoses, fittings, and electric wiring with relays and switches.
530/110 AC KIT
Additional AC System
The model 530 unit was designed for a small commuter, shuttle type vehicle requires an average amount of extra cooling. It is used with items that do not require a refrigerated environment. The unit is powered by twin dual bearing, three speed motors.
BTU Cooling
30,000
CFM
480
Amps at 13.5v
21
Dimensions
33.75W x 12D x 5.5H"
Weight
23.5 lbs
This model 110 Frigiking roof or underbody mounted condenser is a way of providing maximum heat transfer during stop and go operations. Featured are three 11" blades, white aluminum housing and powder coated galvanized mounting brackets.
BTU Cooling
60,000
CFM
4200
Amps at 13.5V
22.5
Dimensions
44.5W x 13D x 13H"
Weight
33 lbs
Compresor,Hardware,Hozes,Switches
This basic kit includes all components need for a complete installation including the above shown evaporator,condenser,heater,hoses, fittings, and electric wiring with relays and switches.
EZ5/110 AC KIT
Additional AC System
The model EZ5 unit was designed for a small commuter, shuttle type vehicle requires an average amount of extra cooling. It is used with items that do not require a refrigerated environment. The unit is powered by twin dual bearing, three speed motors.
BTU Cooling
30,000
CFM
480
Amps at 13.5v
21
Dimensions
33.75W x 12D x 5.5H"
Weight
23.5 lbs
This model 110 Frigiking roof or underbody mounted condenser is a way of providing maximum heat transfer during stop and go operations. Featured are three 11" blades, white aluminum housing and powder coated galvanized mounting brackets.
BTU Cooling
60,000
CFM
4200
Amps at 13.5V
22.5
Dimensions
44.5W x 13D x 13H"
Weight
33 lbs
Compresor,Hardware,Hozes,Switches
This basic kit includes all components need for a complete installation including the above shown evaporator,condenser,heater,hoses, fittings, and electric wiring with relays and switches.
ES5/110 AC KIT
Additional AC System
The model EZ5 unit was designed for a small commuter, shuttle type vehicle requires an average amount of extra cooling. It is used with items that do not require a refrigerated environment. The unit is powered by twin dual bearing, three speed motors.
BTU Cooling
30,000
CFM
480
Amps at 13.5v
21
Dimensions
33.75W x 12D x 5.5H"
Weight
23.5 lbs
This model 110 Frigiking roof or underbody mounted condenser is a way of providing maximum heat transfer during stop and go operations. Featured are three 11" blades, white aluminum housing and powder coated galvanized mounting brackets.
BTU Cooling
60,000
CFM
4200
Amps at 13.5V
22.5
Dimensions
44.5W x 13D x 13H"
Weight
33 lbs
Compresor,Hardware,Hozes,Switches
This basic kit includes all components need for a complete installation including the above shown evaporator,condenser,heater,hoses, fittings, and electric wiring with relays and switches.
917/110/HYDRONIC AC KIT
Additional AC System
The model 530 unit was designed for a small commuter, shuttle type vehicle requires an average amount of extra cooling. It is used with items that do not require a refrigerated environment. The unit is powered by twin dual bearing, three speed motors.
BTU Cooling
30,000
CFM
480
Amps at 13.5v
21
Dimensions
33.75W x 12D x 5.5H"
Weight
23.5 lbs
This model 110 Frigiking roof or underbody mounted condenser is a way of providing maximum heat transfer during stop and go operations. Featured are three 11" blades, white aluminum housing and powder coated galvanized mounting brackets.
BTU Cooling
60,000
CFM
4200
Amps at 13.5V
22.5
Dimensions
44.5W x 13D x 13H"
Weight
33 lbs
Compresor,Hardware,Hozes,Switches
This basic kit includes all components need for a complete installation including the above shown evaporator,condenser,heater,hoses, fittings, and electric wiring with relays and switches.
560/110/HYDRONIC AC KIT
Additional AC System
The model 560 unit was designed for a larger commuter, shuttle type vehicle. It is used with items that do not require a refrigerated environment. The unit is powered by twin dual bearing, three speed motors.
BTU Cooling
30,000
BTU Heating
32,000
CFM
630
Amps at 13.5v
16.3
Dimensions
17.5W x 9.25D x 13H"
Weight
29 lbs
This model 110 Frigiking roof or underbody mounted condenser is a way of providing maximum heat transfer during stop and go operations. Featured are three 11" blades, white aluminum housing and powder coated galvanized mounting brackets.
BTU Cooling
60,000
CFM
4200
Amps at 13.5V
22.5
Dimensions
44.5W x 13D x 13H"
Weight
33 lbs
Compresor,Hardware,Hozes,Switches
This basic kit includes all components need for a complete installation including the above shown evaporator,condenser,heater,hoses, fittings, and electric wiring with relays and switches.
These ProAir kits are part of rear air conditioning and heating systems.